Do-it-yourself garden bench for a summer residence: six projects for every taste

Do-it-yourself garden bench for a summer residence: six projects for every taste


We are searching data for your request:

Forums and discussions:
Manuals and reference books:
Data from registers:
Wait the end of the search in all databases.
Upon completion, a link will appear to access the found materials.

One of the attributes of a garden or recreation area on a suburban area is a bench, sitting on which you can read a book alone or, conversely, spend a few fun hours with friends. How to make an ordinary bench comfortable and at the same time turn into an element of garden decor? The way out is simple - a do-it-yourself bench for a summer residence. Only your own exclusive creation will fully satisfy your personal aesthetic needs.

What is the best way to place benches in a summer cottage?

Before you start a sketch or drawing of a product, you need to think about the place of its installation. The material of manufacture also depends on this. For example, in an old garden with large branchy trees, a wooden bench in a wrought-iron frame looks good (as an option - a product made of a log on a stone base), and in a young garden there is a light, even openwork bench in a romantic style.

A small white bench stands out in contrast against a dark green hedge.

If you place it in a quiet secluded corner, near a pond or surrounded by flowering flower beds, it will become a wonderful place of solitude and relaxation, where you can spend a few pleasant minutes alone with yourself after a hard workout in the beds.

An old brick wall, a gray wood bench and flowers look mysterious and romantic

Benches are often an integral part of verandas, gazebos, summer picnic areas. In this case, there should be several products designed in the same style. One example is a garden table with two benches on the sides, where you can have a family tea party or play board games on a summer evening.

Deliberately rough and comfortable wooden structure - a table, two benches and an armchair

It is better to install the bench in such a way that it opens a view not of the neighbor's fence or garage, but of a pond, a flower garden or a front garden. The surrounding picture should be pleasing to the eye, not a reminder that it is necessary to refuel the car or renew the paint on the gazebo. It is also appropriate to arrange benches on the playground, by the pool, near the main entrance to the house.

A bench by the pond surrounded by flowers and greenery is a great place to relax and think

One of the best places is in the garden, near the beds. It is better if the bench will stand in the shade, for example, under a spreading crown of a tree or under a canopy, since it is intended for rest from physical labor - digging, weeding, watering or harvesting.

Relaxing in the shade of a flowering bush is a real pleasure

You can think of a decorative frame: a do-it-yourself garden bench looks good surrounded by low flowering bushes, specially arranged flower beds, on a small hill or on a site made of natural stone or paving slabs.

Preparatory work is half the battle

First you need to take a piece of paper and make a sketch or drawing of the proposed product. Even at this stage, questions may arise: what height will be optimal or how many legs should the bench have? There are general standards that should be followed during chart design:

  • 400 mm - 500 mm - seat height;
  • 500 mm - 550 mm - seat width;
  • 350 mm - 500 mm - back height.

If you plan to create a product with a back, you should determine for yourself how the back will be attached to the seat. Depending on whether the bench is portable or not, the legs are planned: for a non-portable product, they are firmly fixed in the ground.

It is not difficult to fix the legs of the bench: it is necessary to dig holes of the required size and fill them with cement mortar, lowering wooden parts there

According to the drawing, you can estimate how much material is required for work. Usually, a minimum of financial investment is spent on a product of this kind: in the country there are always a lot of wooden blanks left over from the construction of a house or a bath, fasteners (screws, nails, bolts, staples), paints and varnishes for wood processing.

If you collect the remains of wooden products and blanks from all over the country house, you can come up with an unusual model

There is also the necessary tool in the back room. If the main material for manufacturing is wood, you should prepare: a plane, a saw, a jigsaw, a hammer, sandpaper, a tape measure and a pencil.

Making benches: six easy projects

You will never go wrong by choosing a tree for work - a soft, pliable in processing and at the same time durable material that can serve for more than a dozen years. From wood, you can create elements of various shapes and sizes, curly inserts, volumetric and miniature details.

Project # 1 - a simple bench with a back

If you have difficulties with drawing up a sketch, you can use a ready-made drawing of a garden bench.

All parts are cut according to the dimensions in the drawing

This bench is traditional for city parks; similar specimens can be found at river stations, near theaters or shopping centers - in those places where you have to spend some time waiting. The advantage of this option is the simplicity of the preparation of parts and the speed of assembly. For work, you will need thick bars for support (3 large and 3 smaller), bars or boards for the seat and back.

The color of the parts can be changed using an impregnation or varnish of a darker shade

This model is portable - it can always be rearranged to another, more convenient place. To ensure that it always stands level and does not sway, when installing the supports, it is necessary to monitor the exact location of the parts - even a slight discrepancy will cause the product to skew.

At the end of the work - and this applies to any wood product located on the street - all wooden parts must be treated with a special impregnation against mold or varnished, also containing protective components. Treated wood does not lend itself to moisture, lasts longer and looks like new for a long time.

Related article: Review of wood protection products against moisture, fire, insects and decay

Project no. 2 - bench in classic style

This option is more solid than the previous one. A bench with a rectangular seat and the same back looks great against the background of a house built of any material - wood, brick, stone.

Assembly diagram of armrests and bench backs in classic style

For a change, you can change the color, choose a shade that is closer to country buildings. The back of such a bench is a real find for those who like to dream up and embody their ideas in wood. Straight vertical bars can be replaced with criss-cross bars.

Several people can easily fit on such a bench.

The top horizontal bar would look good if covered with delicate carvings or colored ornamentation. Armrests and legs can also be curly - but it all depends on the desire and skill of the master. To make such a bench for a summer residence, it will take only a few evenings, and you can enjoy your vacation on it for more than one year.

Project number 3 - a table with benches

The family garden set consists of a comfortable table and two fixed benches.

A comfortable and practical table with a couple of benches will come in handy at any cottage

All large parts (table, benches) are assembled separately, and then assembled into a single whole using 4 lower bars - 2 on each side.

Assembly diagram of the whole kit

The table is a table top with criss-cross legs.

Table assembly diagram

The benches are easily assembled from bars or boards of various lengths.

Bench assembly diagram

At the last stage, the benches are first fixed - to give the structure stability, then - the table, exactly in the middle.

Initial assembly - joining benches

Simple in appearance, but comfortable table will become a gathering place for family and friends in the evenings - for communication, evening tea, relaxation.

Such a table with benches can be placed directly on the lawn

You can download more detailed drawings and photos of this project here.

Project number 5 - video master class

Variety of materials, shapes and styles

Wood is a traditional, warm material for making benches, which is why wood products are so different. Instead of bars processed on machines, you can take natural material of natural forms - and this is not just a bench, but a real masterpiece.

The original bench is made from large pieces of sawn and processed logs

It turns out that there are stone benches, but they are appreciated not for functionality, but for aesthetics. You want to sit on a stone product only in the warm season, but you can admire it constantly.

Small stone bench blends harmoniously with the floral landscape

Forged products look refined and elegant, but only a professional blacksmith can create a garden bench with his own hands from metal.

A wrought-iron bench among the riotous colors looks more than appropriate

Combined benches and benches, built of stone and wood or decorated with textile items - capes, pillows, look interesting.

Small pillows in pink and white tones, neatly laid out on the bench, make the garden corner cozy and homely

That's all for today. We hope you found something helpful. If you have any questions or wishes - you are welcome in the comments.

  • Print

Rate the article:

(17 votes, average: 4.6 out of 5)

Share with your friends!


How to make a garden bench with your own hands

At the summer cottage, I really want to have a corner where you can relax and enjoy nature. Such a place cannot be imagined without a beautiful bench. A garden bench made with your own hands can not only save money, but also fulfill the individual needs and ideas of everyone, because there are a lot of options and techniques for making it, and from them you can choose the one that suits you.

DIY garden bench

  • 1 Step-by-step diagram for assembling a garden bench with a table
  • 2 How to choose a place to install a country bench
  • 3 Preliminary steps
  • 4 Mandatory requirements for the bench
  • 5 Design options
    • 5.1 Simple bench
    • 5.2 Classic
    • 5.3 Folding bench for summer cottages
    • 5.4 Metal bench
  • 6 Useful information
    • 6.1 Video - interesting ideas for making a garden bench on your own

Garden bench

In a well-groomed summer cottage comfortable benches, which are located in shady secluded places, occupy an important place. Wooden benches are widely popular, as they are very comfortable, stylish, and made from environmentally friendly materials. A wooden bench with your own hands fits perfectly into the landscape of any site.

It should be noted that garden benches - benches have existed for at least several hundred years as a decorative element of landscape design, attracting attention and at the same time - creating a good, even more to say - a peaceful mood.

They are installed, both in the best gardens in the world, and simply on a hillock by the river that flows beyond the village. The townspeople make dates in the park, at the 5th bench, and the gardeners "hide"Her between the lilac bushes, where you can drink aromatic tea and relax your soul after gardening.

Without a doubt, a beautiful and comfortable garden is worthy of decoration, however, it is more comfortable to admire it while sitting on a comfortable bench in a well-tended corner under the shade of trees.

Undoubtedly, these small architectural forms are a reflection of the owners' taste preferences for a particular style in the garden.


DIY bench: drawings, photos, instructions for making

Do-it-yourself bench: drawings, photo instructions for making. From a bench (stationary or movable) and a bench (portable without helpers), many people began to master the intricacies of craftsmanship.

A do-it-yourself bench is made as easy as shelling pears: in half an hour or an hour without experience and skills. How long will she stay? But it already depends on the knowledge and experience of the master.

Of which you need very few on the bench, but which will become the basis of more serious skills.

The imagination of the craftsmen on the benches plays in full force and it seems limitless in the photo below, only a few samples taken at random. But you want the fruit of creative imagination to please the eye and body longer. Moreover, he will most often serve in the open air.

And here you can no longer do without knowledge of mechanics, strength of materials and materials science. Elementary, without formulas and complex calculations, but obligatory.

The most aesthetically sophisticated product certainly conceals a "weighty, rough", but not always visible mechanical basis and rests on it.

Self-made benches and benches

Bench power circuits

The basis of any supporting structure is its power circuit. It is a kind of skeleton of lines, perhaps imaginary or simulated on a computer. A fundamentally new power circuit, an event in engineering is usually based on a well-known typical design, which seems to be the most suitable for a given case.

This "seems" and concentrated all the experience of the developer: if the original power circuit is chosen correctly, the product will be reliable and durable even if executed carelessly and with errors.

And if not, then, how then do not "lick" the structure and argue, then the most ultra-modern materials with ultra-high technologies will not allow you to get a good-quality product.

Operating loads are applied to the initial power circuit (while in the mind, on paper or on a computer), and the places of their concentration - tricks - are determined.

Then the scheme is finalized, strengthened and, possibly, modified so that the loads from the foci spread over the "bones of the skeleton" as evenly as possible.

Here, the experience of the designer is no less important than when choosing the initial scheme: the more uniformly the entire structure is loaded, the more reliable and durable it will be. Why, for example, DC-3, B-52, TU-96 and R-7 rocket still fly and see no end in sight? That's why.

Finally, according to the design loads, the sections of the parts are determined based on the given material, and their configuration for design purposes or, say, aerodynamics, is maintained so that the desired section is not less than the calculated one with a margin for the properties and quality of the material.

But back to the topic. Such a simple and "oak" product in its very essence, like a bench or a bench, given the stringent requirements for its cheapness, manufacturability at home, simplicity of design and ease of use, make the bench better one of the following. power circuits (see fig. and the list to it)

Examples of power circuits of benches and benches

  1. Self-supporting (pos. 1) - a row of beams forms the seating floor, which is essentially just lying on the supports. Fasteners "work" only to prevent the bench from creeping without load on the parts under the weight of the seated fasteners are excessively loaded.
  2. Volume-beam (pos. 2) - in order to fend off the desire of the supports to disperse to the sides under the weight of the seated, they are fastened with a coupler below. The fastening of the flooring to the side supports is already strong and therefore necessary.
  3. Box-shaped (pos. 3) - 4 support-beam schemes combined into one: 2 longitudinal and 2 transverse.
  4. Support-beam (pos. 4) - the tie is lifted up and at the same time serves as a support for the seat.
  5. Truss (pos. 5 and 6) - jibs, forming stiffness triangles with the initial elements of the circuit, help to spread the stresses.

The self-supporting scheme is the least material and labor-intensive and the most convenient: an amateur master of an average hand makes such a bench in 10-15 minutes, and chat with your feet under it as you want.

However, the flooring strives to sag, and the "legs" of the bench to disperse to the sides. There are ways to avoid this without wasting a lot of unnecessary material and labor, see below for the truth, this requires metal and welding.

The possibilities of design delights are rather limited, but there are also, see also below.

After the support-beam bench of the cantilever scheme, the second is convenience: it is up to 2 m long, carried from place to place by one person. The backrest adjusts without major difficulties.

A completely reliable volume-beam bench can be made entirely of wood. In terms of strength, it is almost not inferior to the box-shaped one, but it requires less material and is more technologically advanced: in its manufacture, you can do with metal fasteners without making joinery connections.

The design possibilities are the same as before. case, but unlike it, it is difficult to attach the back: the load on it forces the screed to bend in the horizontal plane, which violates the distribution of loads in the entire structure.

It is quite comfortable: although you cannot swing your legs from the heart, you can squeeze them.

The box bench is ideal mechanically: in its power scheme, both constant and variable loads of any direction are most evenly distributed, it is not for nothing that the biplane box has survived in aviation to this day. In terms of bearing capacity to weight and volume of material used, the box bench is far ahead of the rest.

The back can be attached as you like, subject to the rules, which will be discussed below. The complete destruction of any of the links forming the box does not deprive such a shop of serviceability, so if necessary, you can not rush to repair. Convenience is the same as before. (volume-beam). The design possibilities are almost unlimited.

Disadvantages - bulkiness, increased material consumption and design complexity.

Important! a bench made of a board on logs dug into the ground or scraps of timber according to the mechanics are also box-shaped, only in a visually implicit form.

The bench of the support-beam scheme requires a minimum consumption of material and is the lightest: a woman can take it out and bring it back into the house up to 2. It can be made without metal fasteners on simple joinery connections and glue available for inexperienced hobbyists.

Disadvantages - you can't attach the back, the bench leads from the very first leg that sits on it, you can't really squeeze it, if the support beam is calculated correctly. Design possibilities are limited to wood carvings, decorative metal plates and shaped cutting of the legs.

But the durability, if made without metal, is extraordinary: in museums of wooden antiquity there are such shops that literally for centuries were dragged out of the hut in the summer, and back in the winter.

Drawings of a support-beam bench of traditional design are given in Fig.:

Drawings of a wooden bench of the support-beam power circuit

The material of the sidewalls and the support beam is a solid board or solid wood (a maple board made of it with dowels or lamellas). If the thickness of the boards is 40 mm, then the length of the bench can be increased to 2 m; if instead of boards, blocks from 50 mm are used, then the width of the seat can also be increased to 45 cm.But in both cases, the legs and the beam must be made of a solid board or chopping blocks.

Truss power circuits are obtained from the initial ones by adding oblique links. This allows for a more even distribution of loads and material savings due to an increase in the amount of labor required and its complexity.

Here you need to remember: farms with less than 2 longitudinal ties do not happen. For example, a bench in the inset in pos. 5 in Fig. not a truss. In it, the braces only help the legs to disperse under load. Such a bench with a length of more than 50 cm, a width of less than 20 and more than 30 cm will not last long.

How to make a garden bench of a truss power circuit, see eg. roller:

Video: DIY wooden garden bench

Important! In volumetric structures, the longitudinal bonds providing the rigidity of the truss can also be implicit, i.e. not directly associated with jibs. For example, in a shop at pos. 6 overall rigidity is provided by the backrest.

If the bench has a back, the design of its side supports is of particular importance. The backrest support pillars, combined with the legs, can both strengthen the structure and weaken it. You can not think about it by making the bench box-shaped or close to it in terms of the properties of the scheme, see below, but you need to think closely about the sidewalls for economical cantilever, volume-beam and truss benches.

The easiest option

It is said above that the box-type power circuit is capable of accepting and absorbing any loads within the allowable size. But the bench is not a hundred-year-old fighter-biplane, it does not need to spin in the sky, and the loads from the back are quite accurately known in size and direction.

Therefore, you can use a more economical, home-like and comfortable volumetric beam scheme, and compensate for the bending load on the screed with the "oak" material for a bench with a length of approx. up to 1.7 m, a running inexpensive pine board 140x40 is enough.

How a simple wooden bench with a back is arranged and the critical units of its structure are shown in fig:

Drawings of a simple wooden bench with a back

For methods of material preparation and finishing (impregnation, varnishing), see the end.

Here you can add that during the work it would not hurt to collect sawdust, and before varnishing, mix them with PVA (3-4): 1 and with the resulting putty fill the holes above the fastener heads (wood screws 70x6). The gaps between the floorboards of the seat and backrest are necessary to prevent capillary moisture from rotting the material.

Important! A wooden bench with a backrest up to 2 in length can be made according to a combined scheme - top from box, bottom with a tie. It is comfortable to sit on such a seat, but not much more material and labor are needed, see eg. video

Video: wooden bench in 6 hours

Why and what kind of triangle is needed

The power circuits of lighter benches with a backrest are usually strengthened by the so-called. stiffness triangles by adding oblique constraints about the stiffness of a triangle from school geometry you probably remember.

But in this case, it just does not mean that the more the better. A small triangle is as rigid as a large one, but the latter greatly reduces the comfort of the bench and the possibilities of its design, pos.

The use of "stiffness triangle" in the construction of garden benches

Many oblique connections and, accordingly, many triangles crammed into the original scheme at random or by necessity (a transforming bench in position 2) may not strengthen, but, on the contrary, weaken the original scheme.

The stiffness triangle works like this: it is set in such a way that, theoretically, the focus of the loads falls on its "hole" - the geometric center.

Then the sides of the triangle will not only take on evenly the load from the focus, but also “shove” it more or less evenly into the long-length parts associated with them.

But if instead of this there is also a triangle, then they, perhaps, will begin to "cram" loads far not to the benefit of the overall strength. In this case, you will not be able to do it by eye, you need a detailed calculation. "By eye" you can put a small triangle of stiffness at a certain point, visible from general and personal experience.

Support options

Fortunately for beginners, over the centuries of general design experience, methods have been developed to strengthen the original power circuits with stiffness triangles, which can be used for irresponsible structures without calculations. Schemes are also well known, unconditionally unacceptable without calculations.

At first glance, the simplest version of the so-called. λ-supports (item 1 in the figure) are given in the courses of applied mechanics and resistance to materials as an example of how not to do it: in the places marked in red, strong unavoidable load focuses are formed, since there is no stiffness triangle as such in this design.

And at the intersection of the "stick" and the "leg" "λ" you cannot do without a connection. Couples wood-steel or wood-wood have to work in it preim. to shift, which both cannot stand. The design of the bench turns out to be simple, and the look is original, there is no dispute, but it will also loosen up soon.

It can also collapse no less original: suddenly under those sitting.

Design options for the side supports of benches with a back

Symmetrical X-shaped support seems to be more reliable because together with the supporting beam of the flooring forms a triangle, pos. 2. But - only if someone settles down on the bench and remains there forever.

In fact, if the seated person leans back, the focus of stress will shift to its connection with the support. And when he starts to get up, he will briefly "jump" on the X crosshairs (this and that is marked in red). Loads in focuses will be much weaker than before.

case, but periodic. They are contraindicated for wood in combination with any other material.

To avoid focusing loads in the material, you need to:

  1. Make X asymmetrical by extending it backward by 15-20%.
  2. Pulling the support rails of the seat deck back will also increase the stability of the bench.
  3. Attach the backrest planks to the rear legs X and the seat beam brackets. An additional stiffness triangle is formed (shown by an arrow in pos. 3).

No matter who does what he does on the bench, the focus of the loads will jump between the "holes" of the triangles and will not be absorbed into the material.

How armrests help

Strengthening a bench with a back is greatly facilitated if armrests are provided. In this case, the supports are made A-shaped. In order for cross member A to reliably keep the legs from moving across, the angle at its apex should not exceed 40 degrees.

Since the armrests will then fall somewhere at the level of the shoulders of the seated person, And they cut off the top and put a tie there, which will at the same time be the support beam of the armrest. Now it is enough to put the backrest stand, and the stiffness triangle is formed exactly where it is needed, pos. four.

Depending on the size and proportions of the bench, the triangle can be located both inward and outward from the rear legs, pos. 5 and 6.

About the size of the shop

Removals of consoles and asymmetry of supports in the pre. case are selected based on the usual sizes of seats for a person - a chair, a stool:

  • Seat height - 42-47 cm depending on height. Typical value - 45 cm
  • Seat width 30-55 cm Typical 40 cm
  • Backrest tilt - 65-85 degrees. Typical is 75 degrees.

Simpler but more convenient

Before we say goodbye to wooden benches for the time being, let's try to make a bench without a back more comfortable. The easiest way to do this is to make the seat concave. But then the "spreading" loads on the legs increase, and the seat loses strength - bent beams hold the load many times worse than straight ones.

The simplest solution to the problem is a box-type power circuit.

Its excess in this case, the overall rigidity will save on material by using thin narrow boards for tsars (furniture screeds, spacers and bearing beams), and for laboriousness - using overlay joints on steel fasteners. Seat rigidity is ensured by the installation of intermediate cross beams, see drawings in fig..

Drawings of a simple comfortable bench without a back


Garden bench for a summer residence with your own hands - 6 projects in photos

One of the attributes of a garden or recreation area on a suburban area is a bench, sitting on which you can read a book alone or, conversely, spend a few fun hours with friends.

How to make an ordinary bench comfortable and at the same time turn into an element of garden decor? The way out is simple - a do-it-yourself bench for a summer residence.

Only your own exclusive creation will fully satisfy your personal aesthetic needs.

What is the best way to place benches in a summer cottage?

Before you start a sketch or drawing of a product, you need to think about the place of its installation. The material of manufacture also depends on this. For example, in an old garden with large branchy trees, a wooden bench in a wrought-iron frame looks good (as an option - a product made of a log on a stone base), and in a young garden there is a light, even openwork bench in a romantic style.

The small white bench stands out in contrast against the dark green hedge.

If placed in a quiet secluded corner, near a pond or surrounded by flowering flower beds, it will become a wonderful place of solitude and relaxation, where you can spend a few pleasant minutes alone with yourself after a labor "warm-up" in the beds.

An old brick wall, a gray wood bench and flowers look mysterious and romantic

Benches are often an integral part of verandas, gazebos, summer picnic areas. In this case, there should be several products designed in the same style. One example is a garden table with two benches on the sides, at which you can have a family tea party or play board games on a summer evening.

Deliberately rough and comfortable wooden structure - a table, two benches and an armchair

It is better to install the bench in such a way that it opens a view not of the neighbor's fence or garage, but of a pond, a flower garden or a front garden. The surrounding picture should be pleasing to the eye, not a reminder that it is necessary to refuel the car or renew the paint on the gazebo. It is also appropriate to arrange benches on the playground, by the pool, near the main entrance to the house.

A bench by the pond surrounded by flowers and greenery is a great place to relax and think

One of the best places is in the garden, near the beds. It is better if the bench will stand in the shade, for example, under a spreading crown of a tree or under a canopy, since it is designed to rest from physical labor - digging, weeding, watering or harvesting.

Relaxing in the shade of a flowering bush is a real pleasure

You can think of a decorative frame: a do-it-yourself garden bench looks good surrounded by low flowering bushes, specially arranged flower beds, on a small hill or on a site made of natural stone or paving slabs.

Preparatory work is half the battle

First you need to take a piece of paper and make a sketch or drawing of the proposed product. Even at this stage, questions may arise: what height will be optimal or how many legs should the bench have? There are general standards that should be followed during chart design:

  • 400 mm - 500 mm - seat height
  • 500 mm - 550 mm - seat width
  • 350 mm - 500 mm - back height.

If you are planning to create a product with a back, you should determine for yourself how the back will be attached to the seat. Depending on whether the bench is portable or not, the legs are planned: for a non-portable product, they are firmly fixed in the ground.

It is not difficult to fix the legs of the bench: it is necessary to dig holes of the required size and fill them with cement mortar, lowering wooden parts there

According to the drawing, you can estimate how much material is required for work. Usually, a minimum of financial investment is spent on a product of this kind: in the country there are always a lot of wooden blanks left over from the construction of a house or a bath, fasteners (screws, nails, bolts, staples), paints and varnishes for wood processing.

If you collect the remains of wooden products and blanks from all over the country house, you can come up with an unusual model

There is also the necessary tool in the back room. If the main material for manufacturing is wood, you should prepare: a plane, a saw, a jigsaw, a hammer, sandpaper, a tape measure and a pencil.

Making benches: six easy projects

You will never go wrong by choosing a tree for work - a soft, pliable in processing and at the same time durable material that can serve for more than a dozen years. From wood, you can create elements of various shapes and sizes, curly inserts, volumetric and miniature details.

Project # 1 - a simple bench with a back

If you have difficulty drawing up a sketch, you can use a ready-made drawing of a garden bench.

All parts are cut according to the dimensions in the drawing

This bench is traditional for city parks, similar specimens can be found at river stations, near theaters or shopping centers - in those places where you have to spend some time waiting. The advantage of this option is the simplicity of the preparation of parts and the speed of assembly. For work, you will need thick bars for support (3 large and 3 smaller), bars or boards for the seat and back.

The color of the parts can be changed using an impregnation or varnish of a darker shade

This model is portable - it can always be rearranged to another, more convenient place. To ensure that it always stands level and does not sway, when installing the supports, it is necessary to monitor the exact location of the parts - even a slight discrepancy will cause the product to skew.

At the end of the work - and this applies to any wood product located on the street - all wooden parts must be treated with a special impregnation against mold or varnished, also containing protective components. Treated wood does not lend itself to moisture, lasts longer and looks like new for a long time.

Project no. 2 - bench in classic style

This option is more solid than the previous one. A bench with a rectangular seat and the same back looks great against the background of a house built of any material - wood, brick, stone.

Assembly diagram of armrests and bench backs in classic style

For a change, you can change the color, choose a shade that is closer to country buildings. The back of such a bench is a real find for those who like to dream up and embody their ideas in wood. Straight vertical bars can be replaced with criss-cross bars.

Several people can easily fit on such a bench.

The top horizontal bar would look good if covered with delicate carvings or colored ornamentation. Armrests and legs can also be curly - but it all depends on the desire and skill of the master. To make such a bench for a summer residence, it will take only a few evenings, and you can enjoy your vacation on it for more than one year.

Project number 3 - a table with benches

The family garden set consists of a comfortable table and two fixed benches.

A comfortable and practical table with a couple of benches will come in handy at any cottage

All large parts (table, benches) are assembled separately, and then assembled into a single whole using 4 lower bars - 2 on each side.

Assembly diagram of the whole kit

The table is a table top with criss-cross legs.

The benches are easily assembled from bars or boards of various lengths.

At the last stage, the benches are first fixed - to give the structure stability, then - the table, exactly in the middle.

Initial assembly - joining benches

Simple in appearance, but comfortable table will become a gathering place for family and friends in the evenings - for communication, evening tea, relaxation.

Such a table with benches can be placed directly on the lawn

You can download more detailed drawings and photos of this project here.

Projects No. 4,5,6 - video master classes

Variety of materials, shapes and styles

Wood is a traditional, “warm” material for making benches, which is why wood products are so different. Instead of bars processed on machines, you can take natural material of natural forms - and this is not just a bench, but a real masterpiece.

The original bench is made from large pieces of sawn and processed logs

It turns out that there are stone benches, but they are appreciated not for functionality, but for aesthetics. You want to sit on a stone product only in the warm season, but you can admire it constantly.

Small stone bench blends harmoniously with the floral landscape

Forged products look refined and elegant, but only a professional blacksmith can create a garden bench with his own hands from metal.

A wrought-iron bench among the riotous colors looks more than appropriate

Combined benches and benches, built of stone and wood or decorated with textile items - capes, pillows, look interesting.

Small pillows in pink and white tones, neatly laid out on the bench, make the garden corner cozy and homely

That's all for today. We hope you found something helpful. If you have any questions or suggestions - you are welcome in the comments.


Watch the video: English Garden Bench - Complete Project Build